Comprehensive test and measurement service provider-Shenzhen Weike Electronic Technology Co.
● Basic power accuracy ±0.05%*1 (*1 refers only to the accuracy of the main unit, but even with the addition of a current sensor, the accuracy can be ±0.075%)
● High interference immunity and high stability (CMRR of 80dB/100kHz, temperature characteristics of ±0.01%/°C)
● It can also accurately measure widely varying loads, TrueHD 18bit
:: 10ms update rate while ensuring the highest accuracy (all measurements are independent and calculated simultaneously through a dedicated IC)
● Important for accurate and stable efficiency measurements: DC basic accuracy ± 0.07%
● Frequency bandwidth DC 0.1 Hz ~ 2 MHz
● High-speed sampling 18 bit, 5 MS/s for reliable frequency analysis
● Maximum 12ch*2, real-time connection of 2 synchronization function
The ※2 6ch model uses an optical connection cable (up to 500m) to connect two units, allowing synchronization of data and waveforms.
● Waveform analysis without oscilloscope, dedicated trigger for motor analysis
:: Bandwidth 1.5 MHz, wideband harmonic analysis up to 100th order
● Transmission of measured values to the Hinoki data collector via Bluetooth® wireless technology-compatible adapter (compatible with LR8410 Link)
Basic parameters
| Measuring Lines | Single-phase 2-wire, single-phase 3-wire, three-phase 3-wire, three-phase 4-wire |
|---|---|
| Number of input channels | Maximum 6ch, voltage/current simultaneous unit is 1ch (Voltage measurement section: optical insulation input, current measurement section: insulation input via current sensor) |
| Measurement items | Voltage (U), Current (I), Active Power (P), Apparent Power (S), Reactive Power (Q), Power Factor (λ), Phase Angle (φ), Frequency (f), Efficiency (η), Losses (loss), Voltage Ripple Ratio (Urf), Current Ripple Ratio (Irf), Current Accumulation (Ih), Power Accumulation (WP), Voltage Peak (Upk), Current Peak (Ipk) ) |
| Harmonic measurement: Harmonic active power, etc., the number of operations from 2 to 100 times to choose from | |
| Waveform recording: Voltage and current waveform/motor pulse: 5MS/s normally, motor waveform: 50kS/s, 16bit Recording capacity: 1MW x (voltage + current) x ch number + motor waveform | |
| Motor Analysis (PW6001-11~-16 only): Voltage, Torque, RPM, Frequency, RPM, Motor Efficiency | |
| measuring range | Voltage: 6 V to 1500 V, 8 ranges |
| Current (Probe1): 400 mA to 1 kA (range varies depending on current sensor) | |
| Current (Probe2): 100 mA to 50 kA (range varies depending on current sensor) | |
| Power: 2.40000W to 4.50000MW (depending on voltage and current sensors) | |
| Frequency: 0.1 Hz to 2 MHz | |
| Basic precision | Voltage : ±0.02% rdg. ±0.02% f.s. Current : ±0.02% rdg. ±0.02% f.s. Power : ±0.02% rdg. ±0.03% f.s. |
| Synchronization frequency range | Power measurement: 0.1 Hz to 2 MHz Harmonic measurement: 45 Hz to 66 Hz (IEC standard mode), 0.1 Hz to 300 kHz (broadband mode) |
| frequency bandwidth | DC, 0.1 Hz ~ 2 MHz |
| Data retention interval | Interval 10ms~, select from all measured values including harmonic measurements, save to memory or USB flash drive |
| connector | USB flash drive, LAN, GP-IB, RS-232C, external control, 2 units synchronized |
| power supply | AC 100 V to 240 V, 50Hz/60 Hz, 200 VA |
| Volume and weight | 430 W × 177 H × 450 D mm, 14kg (for PW6001-16) |
| attachment (email) | Instruction manual × 1, power cord × 1, D-sub 25-pin connector × 1 (PW6001-1x only) |
