GDS-3000A数字存储示波器
GDS-3000A数字存储示波器
GDS-3000A数字存储示波器
GDS-3000A数字存储示波器
GDS-3000A数字存储示波器
GDS-3000A数字存储示波器
GDS-3000A数字存储示波器
GDS-3000A数字存储示波器
GDS-3000A数字存储示波器
GDS-3000A数字存储示波器
GDS-3000A数字存储示波器
GDS-3000A数字存储示波器

GDS-3000A数字存储示波器

¥999,999.00
  
  • Quantity
    • -
    • +
  •    
Inquire about this product
  • 650MHz /350MHz带宽, 2/4 通道
  • 5GSa/s 实时采样率(单通道); 2.5GSa/s 实时采样率(双通道)
  • 每通道200Mpts 记录长度
  • 200,000 wfm/s 的波形更新率
  • 10.2 inch 800*480 TFT LCD显示
  • 490,000 分段存储,波形搜索功能
  • 38 种自动测量功能
  • 高分辨率采集模式
  • I2C/SPI/UART/CAN/LIN 串行总线触发与解码功能
  • 双通道频谱分析仪 (DC~2.5GHz)包含光谱图功能
  • 双通道25MHz 任意波形发生器
  • 13种电源分析测量功能(选配)
  • 选配16通道逻辑分析仪 (MSO)

GDS-3000A系列示波器提供每个通道高达200Mpts的记录长度,超长记录长度的优点允许用户即使在低速时间设置下也能保持较高的采样率。当采样率比测试频率高两倍时,它可以确保捕获的信号没有失真,这有利于在低速下长时间观察信号的变化,这对信号的深入分析非常有帮助。

关于波形更新率,GDS-3000A高达200,000 wfm/s,用户可以轻松观察到零星的异常信号。分段存储器可连续捕获多达490,000个分段,可与触发条件设置配合使用,跳过长时间未改变的波形,只记录有意义的波形,从而提供最有效的内存使用方法。分段内存下还提供掩码功能,允许用户快速确定大量信号是否超出目标范围,并可以快速搜索错误波形的时间和实际信号。

在测量功能方面,提供了38种测量项目。精细刻度功能可使用户根据需要微调垂直刻度,以实现全尺寸测量并提高电压或电流测量的精度。提供了高分辨率模式的采集方法,有效地消除了噪声,提高了自动测量的精度。屏幕显示器右侧提供了动态垂直刻度显示器,使用户更容易解释与测量信号相对应的垂直振幅。

标准的1 MΩ和50Ω输入阻抗的选择允许用户根据不同的测量要求选择输入阻抗,以实现阻抗匹配。搜索功能可以根据用户设置快速查找合格信号,这对于查找和比较零星波形非常有帮助。

光标标记功能允许用户清楚地观察光标测量的点之间的电压(或电流)、时间和增量数据。使用指示器功能,可以通过显示波形的部分来显示测量范围。

在频域测量方面,GDS-3000A提供了FFT测量功能和双通道频谱分析仪。用户可以同时测量和分析双通道频域信号。光谱图功能允许用户轻松观察频谱分布随时间的关系,以便观察信号的频谱特性。

GDS-3000A为开关电源测试提供了丰富的测试项目。提供的电源测试项目包括交流输入分析项目:电源品质、诺波、浪涌电流;直流输出分析所需测试项目:纹波/噪声、瞬态响应分析、开/关分析、效率;控制回路响应(Bode)和电源抑制比(PSRR);完整的开关元件分析项目:调制、开关损耗、SOA( 安全工作区)和磁性分析: B-H 曲线。GDS- 3000A内建50MHz(GCP-530)和100MHz(GCP-1030)电流探棒的电源。此功能可以节省用户购买电流探头电源的成本,减轻外出携带电流探头电源的负担。

GDS-3000A标配双通道25MHz任意波发生器。用户可以选择任意波功能来存储模拟通道测量的信号或直接从信号发生器输出。此功能允许用户方便地生成各种类型的测量信号,以模拟各种信号输出。还配备了频率响应分析功能(Bode Plot),可应用于产品电路和元件特性验证与分析,包括RLC电路设计、滤波器设计和放大器设计验证与分析。

GDS-3000A提供丰富的通信接口。除了常用的USB Host、USB设备端口和LAN端口外,它还包括一个高度稳定的RS232接口和一个选配的GPIB接口。

GDS-3000A norm

本规格适用于GDS-3000A系列在+20°C~+30°C下通电至少30分钟。

GDS-3352A conduit 2 + Ext
bandwidths DC ~ 350MHz (–3dB) @50Ω/1MΩ input impedance
rising time 1ns (calculated)
bandwidth limit 20MHz/100MHz/200MHz*
GDS-3652A conduit 2 + Ext
bandwidths DC ~ 650MHz (–3dB) @ 50Ω input impedance

DC ~ 500MHz (–3dB) @1MΩ input impedance

rising time 535ps (calculated)
bandwidth limit 20MHz/100MHz/200MHz/300MHz*
*带宽限制公差为±10%。

 

垂直灵敏度 resolution (of a photo) 8 bits (Max.12 bits with Hi Res)

For 1MΩ input impedance: 1mV*~10V/div

For 50Ω input impedance: 1mV*~1V/div

Input coupling AC, DC, GND
Input Impedance 1MΩ// 22pF approx.
DC增益精度 1mV: ±5% full scale
≥2mV: ±3% full scale
polarities Normal & Invert
Maximum Input Voltage For 1MΩ input impedance: 300Vrms, CAT II

For 50Ω input impedance: 5Vrms max.

偏移位置范围 For 1MΩ input impedance:

1mV/div ~ 20mV/div :±1V; 50mV/div ~ 500mV/div: ±10V

1V/div ~ 5V/div : ±100V; 10V/div : ±1000V

For 50Ω input impedance:

1mV/div ~ 50mV/div:±1V; 100mV/div ~ 1V/div : ±10V

波形信号处理 +, -, ×, ÷, FFT, User Defined Expression

FFT: Spectral magnitude. Set FFT Vertical Scale to Linear RMS or dBV RMS, and FFT Window to Rectangular, Hamming, Hanning or Blackman.

trig Source CH1, CH2, Line, EXT
Trigger Mode Auto (supports Roll Mode for 100ms/div and slower), Normal, Single
Trigger Type Edge, Pulse Width(Glitch), Video, Pulse Runt, Rise & Fall(Slope), Timeout, Alternate, Event-Delay(1~65535 events), Time-Delay(Duration, 4ns~10s), Bus (UART, I2C, SPI, CAN, LIN)
Holdoff 范围 4ns to 10s
be coupled (with sth) AC, DC, LF rej., HF rej., Noise rej.
(level of) sensitivity 1div
external trigger Range ±20V
(level of) sensitivity DC ~ 100MHz Approx. 100mV
100MHz ~ 350MHz Approx. 150mV
Input Impedance 1MΩ±3%~22pF
*:在1mV/div和2mV/div下,带宽限制为20MHz。
水平 Time base range 1ns/div ~ 1000s/div (1-2-5 increments)
ROLL: 100ms/div ~ 1000s/div
pre-trigger 10 div maximum
后触发 10,000,000 div maximum.
时基精度 ±5 ppm, about ±2ppm increase in error per year
信号采集 real time sampling rate 5GSa/s one channel;

2.5GSa/s dual channels

Record length Max. 200Mpts /CH
采集模式 Normal, Average, High Resolution, Peak Detect, Single
峰值检测 400ps (typical)
on average Selectable from 2 to 256
分段数 1 to 490,000 maximum
X-Y 模式 X-Axis 输入 Channel 1
Y-Axis 输入 Channel 2
phase shift ±3° at 100kHz
光标和测量 光标 Amplitude, Time, Gating available;

Unit: Seconds(s), Hz (1/s), Phase (degree), Ratio (%).

automatic measurement 38 sets with indicator: Pk-Pk, Max, Min, Amplitude, High, Low, Mean, Cycle Mean, RMS, Cycle RMS, Area, Cycle Area, ROVShoot, FOVShoot, RPREShoot, FPREShoot, Frequency, Period, RiseTime, FallTime, +Width, -Width, Duty Cycle, +Pulses, -Pulses, +Edges, -Edges, %Flicker, Flicker Idx ,FRR, FRF, FFR, FFF, LRR, LRF, LFR, LFF, Phase.
光标测量 Voltage difference between cursors(∆V)

Time difference between cursors(∆T)

自动计数器 6 digits, range from 2Hz minimum to the rated bandwidth
控制面板功能 Autoset Single-button, automatic setup of all channels for vertical, horizontal and trigger systems, with “Undo Autoset”, “Fit Screen”/ “AC Priority” mode, and “Fine Scale” functions.
保存设置 20 sets
保存波形 20 sets
保存参考波形 4 sets
电源测量

(Optional)

Power Quality, Harmonics, Ripple, In-rush current, Switching Loss, Modulation, SOA, Transient, Efficiency, B-H curve, Control Loop Response, PSRR, Turn On/Off
AWG general
conduit 2
sampling rate 200MSa/s
vertical resolution 14 bits
Maximum frequency 25 MHz
waveform Sine, Square, Pulse, Ramp, DC, Noise

Sinc, Gaussian, Lorentz, Exponential Rise, Exponential Fall, Haversine, Cardiac

Output range 20 mVpp to 5 Vpp, HighZ;

10 mVpp to 2.5 Vpp, 50Ω

Output Resolution 1mV
输出精度 2% (1 kHz)
偏移范围 ±2.5 V, HighZ; ±1.25 V, 50 Ω
offset resolution 1mV
Sine
frequency range 100 mHz to 25 MHz
flatness
(relative to 1 kHz)
±0.5 dB < 15MHz;

±1dB 15MHz~25MHz

harmonic distortion -40 dBc
杂散(非谐波) -40 dBc
THD 1%
S/N Ratio 40 dB
方波/脉冲波
frequency range Square: 100 mHz to 15 MHz
Rise/fall time < 15ns
overshoot < 3 %
duty cycle Square: 50%

Pulse: 0.4% to 99.6%

Minimum pulse width 30ns
judder 500 ps
斜坡
frequency range 100 mHz to 1MHz
linearity 1%
symmetry 0 to 100%
spectrum analyzer frequency range DC~2.5GHz Max, dual channel with spectrogram (based on Advanced FFT).

Notice: Frequency which exceeds analog front end bandwidth is uncalibrated

Span 1kHz~2.5GHz (Max.)
Resolution bandwidth 1Hz~2.5MHz (Max.)
reference level -80dBm to +40dBm in steps of 5dBm
垂直单位 dBV RMS; Linear RMS; dBm
垂直位置 -12divs to +12divs
垂直比例 1dB/div to 20dB/div in a 1-2-5 Sequence
显示的平均噪声级 1V/div ß -40dBm, Avg :16

100mV/div ß -60dBm, Avg :16

10mV/div ß -80dBm, Avg :16

杂散响应 2nd harmonic distortion < 35dBc

3rd harmonic distortion < 40dBc

频域跟踪类型 Normal; Max Hold; Min Hold; Average (2 ~ 256)
检测方法 Sample; +Peak; -Peak; Average
FFT 窗 FFT Factor:
Hanning 1.44
Rectangular 0.89
Hamming 1.30
Blackman 1.68
逻辑分析仪(选配) sampling rate 1GSa/s
bandwidths 200MHz
Record length Per Channel 10M points (max)
input channel 16 Digital (D15 - D0)
Trigger Type Edge, Pattern, Pulse Width, Serial bus (I2C, SPI, UART, CAN, LIN), Parallel Bus
临界值分组 Settable thresholds for:

D0-D3, D4-D7, D8-11, D12-15

临界值选择 TTL, CMOS(5V,3.3V,2.5V), ECL, PECL,0V ,User Defined
用户定义的临界值范围 ±5V
Maximum Input Voltage ±40 V
最小驱动电压 ±250 mV
vertical resolution 1 bit
Frequency Response Analyzer frequency range 20Hz to 25MHz
输入与输出源 Channel 1 ~ 2
测试点数量 10, 15, 30, 45, 90 points per decade selectable for logarithm scale;

2 ~ 1000 points selectable for linear scale

dynamic range > 80dB (typical)
测试振幅 10mVpp to 2.5Vpp into 50Ω, 20mVpp to 5Vpp into High-Z, Fixed test amplitude or custom amplitude for each decade.
测试结果 Logarithmic or linear overlaid gain and phase plot, may also overlay with reference plots for cross comparison. Test results saved in csv format for offline analysis.
手动测量 Tracking gain and phase markers
绘图尺度 Auto-scaled during test
demonstrate TFT LCD 类型 10.2" TFT LCD WVGA color display
Display resolution 800 horizontal × 480 vertical pixels (WVGA)
内插方式 Sin(x)/x
波形显示 Dots, vectors, variable persistence (16ms~4s), infinite persistence, gray or color waveforms.
波形更新率 200,000 waveforms per second, maximum
显示格线 8 x 10 divisions
display mode YT, XY
connector USB Port USB 2.0 High-speed host port X1, USB High-speed 2.0 device port X1
以太网 (LAN) RJ-45 connector X1, 10/100Mbps with HP Auto-MDIX
Go-NoGo BNC 5V Max/10mA open collector output X1
Power Supply Receptacles ±12V / 600mA for current probe use.

Two sets of power supply receptacles for 2CH models;

RS232C DB-9 male connector X1
VGA 影像输出 DB-15 female connector X1, monitor output for display on VGA monitor
选配的 GPIB 模组 Fully programmable with IEEE488-2 compliance
Kensington 安全锁插槽 Rear-panel security slot connects to standard Kensington-style lock.
(sth. or sb) else 多国语言菜单 Available
operating environment Temperature: 0°C to 50°C. Relative Humidity ≤ 80% at 40°C or below;
≤ 45% at 41°C ~ 50°C.
屏幕帮助 Available
时间功能 Time and Date, Provide the Date/Time for saved data
内建Flash 存储空间 800M bytes Single-Level Cell flash memory
内建APP Go/NoGo, DVM, DataLog, Digital Filter, Frequency Response Analyzer, Mask, Mount Remote Disk, Demo
用户自定义按键 User can select one of the several different preset functions as shortcut key.
额定电压范围与功耗 AC 100V ~ 240V, 50Hz ~ 60Hz, auto selection. power consumption:100W
weights Approx. 4.6kg
sizes 420mm(W)X 253mm(H)X 113.8mm(D)

Standard Accessories

  • User manual CD, Power Cord, Certificate of Calibration
  • GTP-351R:350MHz 10:1 passive probe for GDS-3352A (one per channel)
  • GTP-501R:500MHz 10:1 passive probe for GDS-3652A (one per channel)

 

optional

DS3A-16LA 16 Channel Logic Analyzer
DS3A-GPIB GPIB Interface (factory install)
GTL-248 GPIB Cable, Double Shielded, 2000mm
GTP-033A 35MHz 1:1 Passive probe
GCP-300 300 kHz / 200A Current probe
GCP-500 500 kHz / 150A Current probe
GCP-1000 1MHz / 70A Current probe
GCP-530 50MHz / 30A Current probe
GCP-1030 100MHz /30A Current probe
GDP-025 25MHz High voltage differential probe
GDP-050 50MHz High voltage differential probe
GDP-100 100MHz High voltage differential probe
GKT-100 Deskew fixture
GRA-443-E Rack Mount kit
GTL-232 RS-232C cable, 9-pin female to 9-pin female, Null modem for computer

 

Ordering Information

GDS-3652A
  • 650MHz, 2 channels, Digital Storage Oscilloscope
GDS-3352A
  • 350MHz, 2 channels, Digital Storage Oscilloscope
Expand More
GDS-3000A数字存储示波器GDS-3000A数字存储示波器
¥999,999.00
Purchase of goods

Product consultation and purchase:18218718851

I already understand